SKU, Model, PWM Outputs, Ports, 2 Ports, FASST, Telemetry, S- FHSS, High Speed, High Voltage, Connectors, Range. FUTL, RGF, 4, 0, 0. Updating instructions and software manual are included in the zipped files. Please unzip 12FG Model Recovery Application ( KB) – updated July 23, Futaba 12FG – GHz FASST (T12FGA) with GHz TM Module Accessories included: Instruction Manual – Futaba SD Card – 12 V AC.

Author: Kagagor Vunris
Country: Papua New Guinea
Language: English (Spanish)
Genre: Art
Published (Last): 12 April 2014
Pages: 340
PDF File Size: 6.45 Mb
ePub File Size: 2.25 Mb
ISBN: 332-8-52449-327-7
Downloads: 36431
Price: Free* [*Free Regsitration Required]
Uploader: Sagor

And just fuutaba the 14MZ it offers a viable route into 2. To accomplish this with the Futaba 12FG, I used a variety of stock mixers to control the wings and V-tail. Have regular maintenance performed. Fortunately the battery is easily disconnected from the cutaba board the lead terminates in a standard J-connector. I’ve put it through three transmitters of different brands and it’s broke them all in nicely. Or an unused trim lever can be used to drive an auxiliary channel.

Model addition and call Connect the ailerons, elevators, throttle, rudder, Initial setting assigns 1 model to the T12FG etc.

A good compromise has been struck with the balance. Add conditions, as required.

The timer can be set to count up or down and with or without an alarm at whatever interval you decide. SUB-TRIM The Sub-Trim function is used to set the servo neutral position, and may be used to make fine adjustments to the control surface after linkages and pushrods are hooked up.

Controls have two-character identifiers e. Futaba claim that it offers a faster response.


Futaba 12FG Review

Use the EDIT dial to select the trim box and fuatba push the EDIT button and you will access another screen which enables you to change the trim percentages. I like that very much. After you’ve set your flight conditions, the trim operation can be coupled with among all the conditions which combination mode is selected.

Inevitably though, squeezing so much functionality into a small box has led to one or two compromises that may be noticed especially by those coming from a Euro style box. I often bring multiple things with me to the field when I fly.


All the benefits of PCM-G3 will also apply to the forthcoming 2. When you do not want to 12cgh the Condition Select function, this setting is unnecessary. I don’t personally have a need for that much memory, so I didn’t get a card and cannot comment on its use. Page 98 For more information, see the description at the back of this manual.

So what does the 12FG from Futaba offer?

And with resolution, the response rate is twice as fast as standard PCM receiver’s. If your model of choice is a glider the screen shots would be slightly different as seen below. The preset elevators and flaps camber flap, brake flap offset amount can be activated by a switch.

For detailed information and pictures of these menus, see instruction manual. It futba to shut off the engine with the flip of a switch. Page 77 For a description of the setting method, see the description at the back of this manual. For a while I kept selecting the Model menu instead. Ok, so I setup an old favorite of mine and swapped out the old receiver for the new one that came with the transmitter, futana let’s go fly it. I like the stick tension a little more free than restricted so the factory pre-set felt good to me.


It is used to correct undesirable tendencies when rudder is applied in roll maneuvers, knife edge, etc. For each flying surface, the servo’s can be adjusted to a pre-determined spot. On futzba downside, these adjustments are too crude to match up the movement of large paired control surfaces like flaps, where even the slightest differences in linkage geometry can cause subtle mistracking which is difficult to correct.

When you begin to set up a model, be sure that the digital trims are set to their center position. The nice thing about the 12FG is how the menus for each of the three types of flying disciplines work the same. It’s written largely in ‘Janglish’, many key features are glossed over, and one or two are completely missing. The goals for programming the Futaba 12FG were: You can now adjust the ratcheting in either Mode 1 or 2, again without removing the case.

Idle down setting The Condition Select function automatically allocates The idling speed can be lowered with one touch by is the default condition and is the only one active when a a switch without changing the throttle trim position.